Paint construction has always been an overlooked weakness in home improvement. In fact, most homeowners do not require construction workers to apply any tricks, and they can regulate construction. However, in practice, construction workers are often prone to such phenomena for various reasons: they are not caused to float on the surface of wood lacquer, wrinkled, wrinkled, or granular in size, that is, cracking and delamination of the top surface of the wall. Rusty ... ... in the face of such a horror, the owners can really miserable! In fact, as long as the owners pay attention to the following details during construction, they can effectively avoid many common problems.
Detail 1: Whether the surface of the wood lacquer has obvious flow
The surface of the wood lacquer has obvious flow drop phenomenon. After drying, it forms blemishes and damages the surface.
Supervisor explained: According to the regulations, woodware paintings are not allowed to have obvious edges, falling, wrinkled skin. In addition, the hand touch should be smooth and feel free. Prior to painting, atomic ash is used to make up and polish, and the site must be cleaned. When painting, the ambient temperature should be between 5 °C and 35 °C, and should pay attention to ventilation and dust. In addition, every paint interval is at least four hours.
Detail 2: When the paint is applied, the protection of the furniture is not in place.
The protection of the glass was not in place during painting, and the glass was very ugly and hard to remove.
Supervisor explained: According to the regulations, before the wood painting, the glass and other finished products shall be protected at least two centimeters in width; before the wood painting, the glass and other finished products shall be fully protected. If the paint is inadvertently brushed to a finished product such as glass, it is difficult to clean; even if it is removed, it will cause varying degrees of damage or corrosion to the surface.
Detail 3: Is the construction procedure appropriate?
Due to improper construction procedures, cement is splashed on the brushed wall paint. How hard it is to see is more difficult to see
Supervision explanation: According to the regulations, the indoor finishing project shall be conducted only after the plastering, suspended ceiling and ground leveling equalization projects have been completed and accepted. If the construction process is disrupted, individual construction such as leveling or paving the floor will cause unnecessary damage to the already painted wall. Not only is it difficult to clean up, but it also causes a noticeable color difference in the entire wall.
Detail 4: Does the wall top paint have delamination or shedding?
Wall lacquer delamination, shedding phenomenon should be repainted immediately
Supervisor explained: According to regulations, the adhesive strength of putty used in the finishing project should meet the current national standards. If the strength due to putty can not reach, or putty and the original wall is not firmly bonded, or empty putty itself, due to putty paint easily absorbed paint water, make putty easy to delamination, and even fall off. Therefore, it is recommended that you do a good job of checking before painting.
Detail 5: Whether the wall surface cracks after painting
Due to insufficient sanding before painting, the walls crack after painting
Supervision explained: According to the regulations, there should be no cracking, coarse sandpaper printing, blistering, brushing, etc. after the top paint roller. During the decoration process, if you encounter the inner insulation wall or the light body with poor quality, you should first apply a layer of fiber mesh or fine gauze, and then putty. Then put the putty into place with a suitable number of sandpaper. Finally, when brushing paint, water must be stricken according to the specified proportion.
>>>Related links: How to apply paint imitation enamel paint correctly
Construction Acceptance Paint Glass Coating Interior Decorating Home Furnishing Glass Brick Glass Furniture
Focusing Lenses. The focusing lens is the last optic in the laser path, before it hits the workpiece. Its main role is to focus the laser beam to a specific focal length (FL) - depending on the application. Therefore, the focal length - that is dictated by the radiuses and curvatures of the lens - is its most important feature.Focusing the beam ,produces a focus of high energy density that processes the work piece Product characteristics: • High design accuracy, high precision machining, all systems have reached the diffraction limit •The focus is deep, good consistency across the focal depth range Plane-convex focusing lens is applied to CO2 laser. One side is flat and the other side is convex. The substrate is laser-grade CVD ZnSe and coated with the double-sided anti-reflective film. The convex surface should face the perpendicular incident light beam and the plane should face the workpiece. Meniscus focusing lens is concave and convex focusing lens. The substrate is laser grade CVD ZnSe and coated with the double-sided anti-reflective film. Meniscus focusing lens can effectively reduce spherical aberration and produce smaller light spot than plane-convex focusing lens. The convex surface should face the perpendicular incident light beam and the concave surface should face the workpiece.
Focusing Lens,Led Focusing Lens,Optical Focus Lens,Focus Glass Lens
Changchun Ruiqi Optoelectronics Co.,Ltd , https://www.ruiqi-optics.com