The appearance of the profile should be observed. The color should be blue-white, not white, which is usually considered by people. Pay attention to whether the color of the frame and the fan profile of the door and window is consistent, whether the appearance is uniform and whether the cavity distribution is reasonable. In the formulation of steel door and window profiles, calcium carbonate is usually added as the filler material, and some manufacturers reduce the cost. If the amount is too much, it becomes a calcified plastic. The surface of doors and windows made of this plastic lacks luster and is slightly rough. Hard and brittle, it looks like a rough feeling like stones, normal steel doors and windows, the surface is usually shiny, very tough. Second, the gap between the doors and windows and the seal to see if the various parts of the fit between the clearance is tight, with the Department of the incision is flush, the height of the profile lap joints and so on. General steel doors, the main part of consideration is the door frame, the gap between the fan, the door trim and the door edge, the various sections of the shutter connection, seals, etc.; if assembled door panel, but also consider the door Gap; is to open the door but also whether the two doors closed after the light and so on.
Similarly for the use of plastic steel windows, in addition to the assembly of a variety of profile assembly clearance to be considered, the sealing strip is uniform and solid is also very important, the interface gap should not exceed 1mm, which reflects the window sealing performance. Steel doors usually do inner door of the building, so no high sealing requirements. Various clearance values ​​are stipulated in national standards, but for customers, the smaller the gap value at various profile connections, the tighter the fit and the more exquisite the assembly process, which reflects the assembly level and the accuracy of the assembly tools. Third, the welding of steel doors and windows depends on whether the weld is flush, whether there are cracks, clean corners inside and outside clean and beautiful, with a box ruler measure the diagonal size of steel doors and windows, the diagonal size difference should not be greater than 3mm, the smaller the diagonal difference, the finer the process, and the easier it is to install. Fourth, the hardware quality of hardware and steel doors and windows on the quality of the windows and doors also have a certain impact on the use of hardware looks should be thick, and the surface gloss is better, the protective layer is dense, there is no hit scratch phenomenon, the most important The point is that opening should be flexible.
Fifth, reinforced steel doors and windows reinforced steel in accordance with national standards on the steel doors and windows of the wind pressure have different requirements, plastic steel doors and windows of the frame, the fan's inner cavity to be equipped with reinforced steel, depending on the height of 1.2mm, 1.5mm, 2.0mm three The thickness of reinforced steel to ensure the product's robustness and longevity. In order to reduce costs, some manufacturers do not install or load reinforced steel that does not meet the requirements. Customers in the purchase of products is to pay special attention, usually the inspection methods are: 1, the reference weight method estimates, that is, the weight of the nickname doors and windows, equipped with reinforced steel doors and windows weight, otherwise it is light. 2. Use a magnet to place the frame and fan on the door and window. If the magnet is adsorbed, there will be reinforced steel in the profile, and vice versa. 3. Observe the frame of the door and window, whether there are screws fastening the steel on the fan, it can also prove whether there is reinforced steel. In short, customers should be cautious when choosing products, try to use regular manufacturers' products, and strictly inspect them so as not to be deceived. 2, buy plastic doors and windows notes:
Do not buy cheap steel doors and windows that attach importance to glass and hardware. The glass should be smooth and dry. The glass and plastic profiles are not in direct contact and there is a sealing bead that closes the gap. The hardware is complete, the position is correct, the installation is firm, and the use is flexible.
The surface of doors and windows should be smooth and flat, and there should be no open welding breakage. The sealing strip should be flat, without curling, no groove removal, and no smell on the strip. When doors and windows close,
There is no gap between the fan and the box.
Four doors and windows are all integrated and screwless.
Sliding doors and windows open and slide freely, soft sound, no dust off.
Special steel linings are embedded in the window frames and fan profiles.
The glass should be flat and securely mounted. The installed glass does not directly contact the profile. Glass glue cannot be used. If it is a double glass flat layer, there should be no dust and moisture in the interlayer. Switch parts are tightly closed and flexible. Plastic steel doors and windows are processed in the factory workshop with professional equipment and cannot be made on the construction site.
Door and Window Hardware Window Glass Switch Blinds Craft Glass Glass Sliding Door Glass Door Shutters
China High Speed Centrifuge,Ultra High Speed Centrifuge manufacturer, choose the high quality High Speed Refrigerated Centrifuge,High Speed Centrifuge Rpm, etc.
High Speed Centrifuge,Ultra High Speed Centrifuge,High Speed Refrigerated Centrifuge,High Speed Centrifuge Rpm
Zenith Lab (Jiangsu) Co.,Ltd , https://www.zenithlabo.com